08-12-2008, 04:36 PM | #1 |
Junior Member
Join Date: Jul 2008
Posts: 11
Thanks: 0 Thanked 1 Times in 1 Posts |
delay in dialing out!
I've searched, but didn't find anything!
My Vox has 4 registered providers (Acanac, Voicenetwork, Eutelia and Pennytel). I use Acanac for most of my inbound needs, and only use Acanac for my outbound needs. My issues that started in the last few days or so are: 1. There is a significant delay after I dial the number before it rings. I mean, if I finish dialing 4169671111, there is about 15 seconds of "dead air" before it rings the far end. Why? My dial plan with Vox is the following: Priority = 10 (nothing else smaller is active) If number equals = nxxnxxxxxx Then route to = Acanac My dial plan in my PAP2-NA is the following: (*[56]00S0 |911S0|*xxx[x*]. |x |*xx |1[89]76x.! |1[79]00x.! |1[2-9]xx[2-9]xxxxxxS0 |#x1[2-9]xx[2-9]xxxxxxS0 |011xx. |411S0 |<416:1416>[2-9]xxxxxxS0 |#x<416:1416>[2-9]xxxxxxS0 |<647:1647>[2-9]xxxxxxS0 |#x<647:1647>[2-9]xxxxxxS0 |<905:1905>[2-9]xxxxxxS0 |#x<905:1905>[2-9]xxxxxxS0|P5 <:??????????> ) The ?'s at the end is for my "hot ring" settings if nothing is dialed for 5 seconds. I'm sure I can tweak this more, but it's taken right from the Tutorial found here 2. Randomly, audio disappears either at the beginning of the call, or at various lengths in the call. This issue has plauged me for both inbound and outbound calls (inbound tested through Acanac and Voicenetwork, and outbound only tested through Acanac). Again, settings were followed from the PAP tutorial link provided above. All test calls to *500 and *600 are always fine! Is there any other way I can duplicate the errors? BTW, I've got port forwarding setup in my router (running DD-WRT). The ports forwarded were the standard (16384-16428 I think...). I saw these numbers on one of the posts here! I'm beginning to question my payment to Vox. Ever since I've got VoIP working through here, I've had more issues than smooth sailing. Before Vox, my ATA was the only piece of hardware, and no such issues came through there! Any knowledgeable souls care to take a shot at either, or both? thanks, Sprinter. Last edited by sprinter; 08-12-2008 at 05:32 PM. Reason: More info |
08-13-2008, 05:32 AM | #2 | |
Join Date: Jul 2007
Location: Toronto, Canada
Posts: 1,422
Thanks: 123 Thanked 369 Times in 282 Posts |
1. First, I suggest dumming down your Dial Plan to this (it should continue to do everything your current one does):
(<:1>[2-9]xx[2-9]xxxxxxS0|011xx.|1[2-9]xx[2-9]xxxxxxS0|*xx|[*#x][*x].) 2. A few highlights that may help with incoming calls -Preferably make sure you have STUN set up in your ATA (stun.xten.com has been working for me) -If you are behind a router that has UPnP, make sure it's active -This is optional, but it may help to open these port ranges and forward them to your ATA's IP: 5050-5064 5000-5005 16384-16482 (This is a bit hardware/software specific, but it is the correct range for the PAP2) -Take a look at this if it helps: Setting up Linksys PAP2 - Voxalot FAQ -I'd suggest this codec string in your Provider setup in VoXalot: ulaw;alaw;g726;g729;ilbc;gsm -You may also want to consider Audio Optimization: HowTo: 6 Steps To Optimize Your Audio - Voxalot FAQ Confirming things are working: Outgoing Calls : Can you reach *600 (Echo Test) Incoming Calls: Can you reach the ATA via SIPBroker or the EziDial Quote:
You can speed up dialing delays by entering # after you have dialed the number you wish to call Last edited by emoci; 08-13-2008 at 05:36 AM. |
|
08-14-2008, 02:21 PM | #3 | |||||||
Junior Member
Join Date: Jul 2008
Posts: 11
Thanks: 0 Thanked 1 Times in 1 Posts |
Quote:
Quote:
Already active! Quote:
Quote:
Quote:
Quote:
Quote:
However, if I use EziDial, echo test (or ATA) is reachable...and the NAT handling settings of YES or NO both work! Thanks for this...it does speed up "sending" the dialed number faster! |
|||||||
08-14-2008, 05:25 PM | #4 | |
Join Date: Jul 2007
Location: Toronto, Canada
Posts: 1,422
Thanks: 123 Thanked 369 Times in 282 Posts |
Quote:
The First: Handle VIA received: Yes Handle VIA rport: Yes Insert VIA received: Yes Insert VIA rport: Yes Substitute VIA Addr: No Send Resp To Src Port: No STUN Enable: Yes STUN Test Enable: No STUN Server: stun.xten.com EXT IP: (blank) EXT RTP Port Min: (blank) NAT Keep Alive Intvl: 20 (or 30) or The Second (this is the one I'm using with my PAP2): Handle VIA received: No Handle VIA rport: No Insert VIA received: No Insert VIA rport: No Substitute VIA Addr: Yes Send Resp To Src Port: Yes STUN Enable: Yes STUN Test Enable: No STUN Server: stun.xten.com EXT IP: (blank) EXT RTP Port Min: (blank) NAT Keep Alive Intvl: 20 (or 30) Setup each profile in turn , and then retry to see if you can get things working with Symmetric NAT disabled: HowTo: 6 Steps To Optimize Your Audio - Voxalot FAQ BTW, the port ranges you've opened (you opened both TCP/UDP right? ) |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem dialing to my number | rlmariz | SIP Broker Support | 2 | 05-12-2007 07:15 PM |
Delay when other person answers | kheaver | Voxalot Support | 4 | 03-30-2007 12:23 AM |
Web Callback Delay | jpm | Voxalot Support | 10 | 10-13-2006 07:22 AM |
How Voxalot handels dialing errors | Wortelstok | Voxalot Support | 0 | 08-28-2006 07:54 AM |
4 to 5 Second Delay between Transfer (SIP Registration Service) | richard | Voxalot Support | 2 | 06-03-2006 11:21 PM |