![]() |
|
Voxalot Support Support for the Voxalot service. |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Junior Member
Join Date: May 2006
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() I tried to set up my Cisco 7960, ATA Leadtek 8051, softphone Jphone.
but non of them could get incoming ring! Outgoing call looks OK, I can dial 600 or 500! but no incoming call, my phone have never ring! what is the problem ? Last edited by cgigate; 05-04-2006 at 05:23 AM. |
![]() |
![]() |
![]() |
#2 | |
Junior Member
Join Date: Mar 2006
Posts: 25
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() Quote:
|
|
![]() |
![]() |
![]() |
#3 |
![]() ![]() Join Date: Apr 2006
Location: Vancouver, BC
Posts: 296
Thanks: 94 Thanked 53 Times in 27 Posts ![]() |
![]() We're suffering this problem at my parent's place.
Setup is: a) ATA: SPA-2002 with STUN enabled (specifically Substitute VIA Addr & Send Resp To Src Port: Yes) plugged in router b) Router: Belkin Pre-N Wireless router (symmetric NAT), anti-hacker "firewall" disabled but NAT still in place, SPA-2002 private IP in the Belkin DMZ c) Internet: cable modem (1 Mbps up, 6 Mbps down) The SPA-2002 is registered on line one with Voxalot. Can call out fine. Can only be called by 'phoning' the user@ipaddress directly. Calling user@voxalot.com fails (caller hears long pause then a fast busy signal). This seems to be caused by the Belkin. This problem is not observed on my very similar setup at a different location with a full cone NAT D-Link router. |
![]() |
![]() |
![]() |
#4 |
Junior Member
Join Date: May 2006
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() My Cisco 7960' setting is pretty straight,
SIP proxy server:voxalot.com port: 5060 user name: voxlot# password: my password I attach Cisco 7960 to internet directly, it still cannot ring, all incoming call to VM directly. Call another Voxlot user is OK. |
![]() |
![]() |
![]() |
#5 |
![]() ![]() Join Date: Apr 2006
Location: Vancouver, BC
Posts: 296
Thanks: 94 Thanked 53 Times in 27 Posts ![]() |
![]() Yeah, my problem is different, and probably symmetric NAT related. We get a long pause then a fast busy, not a direct to voice mail call. Normally your problem is caused when your phone/ata is not continually registered with the VOIP provider--when it will register to make an outgoing call (which would appear to work fine) but all incoming calls go to VM because it appears that your ata/phone is not presently registered with the provider and they don't have a device to ring when they get a call.
|
![]() |
![]() |
![]() |
#6 | |
Junior Member
Join Date: Mar 2006
Posts: 25
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() Quote:
2. Try shorting interval cisco reregisters with server (let's say 5 minutes==360 seconds) 3. Try using sipbroker ezidial and see if you can dial yourself (www.sipbroker.com). You have to be signed in to use ezidial. 4. Use stun-server Good luck. Last edited by alfredwesterveld; 05-09-2006 at 11:04 PM. |
|
![]() |
![]() |
![]() |
#7 |
Junior Member
Join Date: May 2006
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() It looks Voxalot not working on Cisco 7960.
I can only dial out 600 and 500, all other numbers get fast busy. no incoming calls Last edited by cgigate; 05-10-2006 at 05:09 AM. |
![]() |
![]() |
![]() |
#8 |
![]() ![]() Join Date: Feb 2006
Posts: 2,930
Thanks: 528 Thanked 646 Times in 340 Posts ![]() ![]() ![]() ![]() ![]() ![]() |
![]() If you can only call 500 and 600 then it is an authentication issue.
1. Check your credentials are ok including the authentication realm=voxalot.com. On the Cisco phones this defaults to the network domain name. 2. Can you trap the reply messages you are receiving back from VoXaLot. The reply message will tell you exactly what the problem is.
__________________
Martin Please post support questions on the forum. Do not send PMs unless requested. Last edited by martin; 05-10-2006 at 05:44 AM. |
![]() |
![]() |
![]() |
#9 |
Junior Member
Join Date: May 2006
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts ![]() |
![]() Finally, I fixed the issue.
It was Cisco firmware not compatible. I changed to latest firmware 8.02. Now it works beautiful, message red LED is very nice when new message in the voice box! |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Voxalot and Sipura/ATA Tutorial: A Comprehensive Walkthrough | ctylor | Voxalot General | 5 | 04-28-2010 12:52 AM |
mynetfone incoming call problem with voxalot acct | sida168 | Voxalot Support | 0 | 05-19-2007 01:06 AM |
C450IP does not ring on incoming calls / part 2 | pranzo | Voxalot Support | 0 | 02-25-2007 12:42 PM |
Call Quality and Voxalot | shibukraj | Voxalot Support | 1 | 12-01-2006 03:39 AM |
DID pointing to Voxalot and Call Quality | pmerrill | Voxalot Support | 9 | 05-23-2006 12:20 AM |