Problem: stun.voxalot.com

pday · 05-26-2009, 03:48 PM

It seems stun,voxalot.com is broken. As can be seen below, I'm on an open internet connection but I still can't get to stun.voxalot.com.

patrick@Sputnik2:~$ stun numb.viagenie.ca
STUN client version 0.96
Primary: Open
Return value is 0x000001
patrick@Sputnik2:~$ stun stun.voxalot.com
STUN client version 0.96
Primary: Blocked or could not reach STUN server
Return value is 0x00001c

carlosalbffgomes · 05-26-2009, 09:16 PM

Me too!
+----------------------------------------------------------------------------+
cagomes@cagomes-laptop:~$ stun stun.voxalot.com
STUN client version 0.96
Primary: Blocked or could not reach STUN server
Return value is 0x00001c
+----------------------------------------------------------------------------+
cagomes@cagomes-laptop:~$ stun stunserver.org
STUN client version 0.96
Primary: Independent Mapping, Port Dependent Filter, preserves ports, no hairpin
Return value is 0x000017
+----------------------------------------------------------------------------+

martin · 05-27-2009, 11:03 AM

This problem should now be resolved. Please let use know if it is still a problem?

carlosalbffgomes · 05-27-2009, 12:45 PM

It's fixed. Thanks.

cagomes@cagomes-laptop:~$ stun stun.voxalot.com
STUN client version 0.96
Primary: Indepndent Mapping, Port Dependent Filter, preserves ports, no hairpin
Return value is 0x000017

boatman · 05-27-2009, 06:47 PM

Sometimes it's possible configure a SIP device (behind a NAT router) to work without stun. This allows phone service to continue no matter if the stun server is working. These instructions are for a Linksys ATA but also work for some other SIP hardware and software.

1. In the router, forward the SIP ports and the RTP port range to the ATA.
2. Set "STUN Enable:" no
3. Set "NAT Keep Alive Enable:" no
4. In order for the ATA to know it's public IP address, make sure the ATA is registered with at least one SIP registrar, or enter your public IP address into the appropriate setting in the ATA (in Linksys ATAs this setting is "EXT IP:").

05-26-2009, 03:48 PM	#1
pday Junior Member Join Date: May 2009 Posts: 1 Thanks: 0 Thanked 0 Times in 0 Posts	Problem: stun.voxalot.com It seems stun,voxalot.com is broken. As can be seen below, I'm on an open internet connection but I still can't get to stun.voxalot.com. patrick@Sputnik2:~$ stun numb.viagenie.ca STUN client version 0.96 Primary: Open Return value is 0x000001 patrick@Sputnik2:~$ stun stun.voxalot.com STUN client version 0.96 Primary: Blocked or could not reach STUN server Return value is 0x00001c

05-27-2009, 11:03 AM	#3
martin Join Date: Feb 2006 Posts: 2,930 Thanks: 528 Thanked 646 Times in 340 Posts	This problem should now be resolved. Please let use know if it is still a problem? __________________ Martin Please post support questions on the forum. Do not send PMs unless requested.

05-27-2009, 12:45 PM	#4
carlosalbffgomes Senior Member Join Date: May 2008 Location: Portugal and Brazil Posts: 107 Thanks: 7 Thanked 26 Times in 21 Posts	Fixed! It's fixed. Thanks. cagomes@cagomes-laptop:~$ stun stun.voxalot.com STUN client version 0.96 Primary: Indepndent Mapping, Port Dependent Filter, preserves ports, no hairpin Return value is 0x000017

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Help with complex problem	elleff	Voxalot Support	0	06-27-2007 01:16 PM
Incoming call problem	pironato	Voxalot Support	18	06-21-2007 11:25 AM
Strange loopback problem	tuttle	Voxalot Support	1	02-12-2007 02:58 AM
Is any Problem with Voxalot Service now?	shibukraj	Voxalot Support	8	11-05-2006 07:07 PM
Pennytel, Buzz problem	Nathanc	Voxalot Support	17	06-28-2006 12:20 AM

05-26-2009, 09:16 PM	#2
carlosalbffgomes Senior Member Join Date: May 2008 Location: Portugal and Brazil Posts: 107 Thanks: 7 Thanked 26 Times in 21 Posts	Me too! +----------------------------------------------------------------------------+ cagomes@cagomes-laptop:~$ stun stun.voxalot.com STUN client version 0.96 Primary: Blocked or could not reach STUN server Return value is 0x00001c +----------------------------------------------------------------------------+ cagomes@cagomes-laptop:~$ stun stunserver.org STUN client version 0.96 Primary: Independent Mapping, Port Dependent Filter, preserves ports, no hairpin Return value is 0x000017 +----------------------------------------------------------------------------+

05-27-2009, 06:47 PM	#5
boatman Senior Member Join Date: Jul 2007 Location: Oregon, USA Posts: 365 Thanks: 17 Thanked 77 Times in 64 Posts	Sometimes it's possible configure a SIP device (behind a NAT router) to work without stun. This allows phone service to continue no matter if the stun server is working. These instructions are for a Linksys ATA but also work for some other SIP hardware and software. 1. In the router, forward the SIP ports and the RTP port range to the ATA. 2. Set "STUN Enable:" no 3. Set "NAT Keep Alive Enable:" no 4. In order for the ATA to know it's public IP address, make sure the ATA is registered with at least one SIP registrar, or enter your public IP address into the appropriate setting in the ATA (in Linksys ATAs this setting is "EXT IP:").