|
Voxalot Support Support for the Voxalot service. |
Thread Tools | Display Modes |
09-30-2009, 10:20 PM | #1 |
Junior Member
Join Date: Sep 2009
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts |
One outbound provider works, other doesn't
Hi, I've just started up and have been receiving calls with Gizmo without a hitch. However, outgoing is a different story. At first, I thought outgoing was working fine as well. Then, I finally got past the 3 minute mark and realized I was calling through Gizmo. When I switched my outgoing to Betamax, suddenly when I called, the other party couldn't hear me, though I could hear them.
Now, usually, I would assume it's the VOIP connection or router, but under this circumstance it seems to me it's gotta be on voxalot's end. Are the any special settings I need to enter under the providers tab? I don't see much of difference in option except that gizmo is registered and that webcalldirect is not but that shouldn't matter for outgoing right? Any ideas? |
10-01-2009, 04:08 AM | #2 |
Join Date: Feb 2006
Posts: 447
Thanks: 4 Thanked 8 Times in 8 Posts |
One-way audio problem are frequently (nearly always?) caused by routing/router/NAT issues. The first step is to try using a STUN server if you're not already. The next is to forward the RTP range of ports, and if still having problems, the SIP port(s).
|
10-01-2009, 02:07 PM | #3 |
Junior Member
Join Date: Sep 2009
Posts: 5
Thanks: 0 Thanked 0 Times in 0 Posts |
STUN is on and port forwarding is also done. So... that's not the problem.
However, even if it was, I don't understand why Gizmo would work but Betamax wouldn't? Why would gizmo get through the ports but not betamax. Afterall, it's all PAP2 -> voxalot -> gizmo/betamax. Wouldnt the fact that gizmo connects indicate that it's a voxalot -> betamax problem and not a PAP2 ->voxalot problem by the virtue that the port works fine. |
10-01-2009, 07:00 PM | #4 |
Senior Member
Join Date: Jul 2007
Location: Oregon, USA
Posts: 365
Thanks: 17 Thanked 77 Times in 64 Posts |
I can't be sure without doing some research, but if you have "NAT Mapping Enable" off then it may be something to do with that.
First, set "Symmetric NAT Handling" to 'Yes' in your Voxalot account. Then install the following settings to your ATA and test again. Let us know if problem is resolved or not. (under SIP tab) Handle_VIA_received: yes Handle_VIA_rport: yes Insert_VIA_received: yes Insert_VIA_rport: yes Substitute_VIA_Addr: yes Send_Resp_To_Src_Port: yes STUN_Enable: yes STUN_Test_Enable: yes STUN_Server: stun.voxalot.com:3478 (or any STUN server such as 'stun01.sipphone.com:3478' or 'stun.sipgate.net:10000') NAT_Keep_Alive_Intvl: 179 (if your phone does not ring try 119 or 59, use highest number that works) (under Line_1 and Line_2 (or PSTN_Line) tabs) NAT_Mapping_Enable: yes NAT_Keep_Alive_Enable: yes NAT_Keep_Alive_Msg: 0000 NAT_Keep_Alive_Dest: $PROXY Register Expires: 3600 ---------- Optional settings, steps 1 - 4: Sometimes its preferable to operate the ATA independently of a STUN server. The benefit is that phone service can continue no matter if the STUN server is working. See steps 1 to 4 below. 1. Forward the SIP ports and the RTP port range from the router to the ATA. 2. Set "STUN Enable:" no 3. Set "NAT Keep Alive Enable:" no 4. The ATA must learn it's public IP address, either through normal SIP registration, or place your public IP address in the 'EXT IP:' field). |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Voxalot and Sipura/ATA Tutorial: A Comprehensive Walkthrough | ctylor | Voxalot General | 5 | 04-28-2010 12:52 AM |
Voice Service Provider registration problem. Help! | 505117 | Voxalot Support | 12 | 09-08-2009 07:03 PM |
Provider with Outbound Proxy? | MrHatken | Voxalot Support | 14 | 03-07-2008 05:02 AM |
Using a local provider | Tranworld | Voxalot Support | 10 | 02-23-2007 04:07 AM |
Outbound routing | MarkosJal | Voxalot Support | 2 | 05-22-2006 10:13 AM |