04-01-2008, 03:55 PM | #1 |
Junior Member
Join Date: Apr 2008
Posts: 4
Thanks: 0 Thanked 1 Times in 1 Posts |
help with addpac 200
Is any one familiar with setting up the addpac 200 devices?
I have one I set up on voxalot about 2 years ago. just the basic sip to sip service. It worked extremely well on a 128/128 inet service thats is bit of a struggle with xlite or similar. In those days it was voxalot.com, and I set up on an ip from the dns lookup of the day.(64.34.163.35) Some time after au.voxalot.com happened it stopped working for inwards calls but always worked for outgoing to another sip device set up in the same manner. however it could not be called from a device on au.voxalot.com set up more recently. I have just reconfigured it to use a dns and au.voxalot.com. But even though it says its registered to the server (and the ip found match's a dns lookup on au.voxalot,com) it gives just busy signal as soon as you lift the handset. like the fx port is not linked to the gateway. For starters I would like to get a full configuration from it, plus I need to confirm its set to the most economical bandwidth codec Its a very powerful and flexible device, but with so many clever options its a pig to configure. If any one can help pls drom me a note or mail, harrycam2@gmail.com hca |
04-02-2008, 10:23 AM | #2 |
Junior Member
Join Date: Apr 2008
Posts: 4
Thanks: 0 Thanked 1 Times in 1 Posts |
followup: how to get it running
For any one else who has one here is a starter. Its a very powerful and flexible device, the available documentation I have found is good but not quite ideal to sort one out.
preferably telnet to it on the serial port at 9600 or else on its ip. default login is root/router "show sip" is a handy command. you may need to enable the ftp server but easiest is to access the device config on ftp and download the config.cfg file. edit it and upload it again and reboot the device from the telnet command line. If it does not seem to work make sure its not overwritten your uploaded file with the running settings. below is a config that works, it is not perfect or optimal. addpac 200B is behind a router gateway on x.x.x.251, available b/w is 128/128 thus the preferred codec. device ip is x.x.x.110 device does not use dhcp, and does not generate it. ( i liked fixed ips on my network) ether 0/0 is to router, ether 0/1 is to other computers if you use qos bandwidth control. Addpac is transparent in this mode. phone is only plugged to fx0, I have not attempted to set it up with 2 phones and sip numbers. note** your voxalot number replaces 123456 in 3 places and password xxxx in 2 places change dnshost to your dns, change ip address and gateway to your desired ip change route to your gateway ! hostname AP200 ! dhcp-list 0 type server dhcp-list 0 address server interface ether0.0 dhcp-list 0 option dhcp-lease-time 7200 ! dhcp-list 1 type server dhcp-list 1 address server 10.1.1.2 10.1.1.254 255.255.255.0 dhcp-list 1 option dhcp-lease-time 600 ! ! ip-share enable ! interface ether0.0 ip address 192.168.2.110 255.255.255.0 qos-control 200 100 ! interface ether1.0 no ip address ! snmp name AP200B ! no arp reset ! route 0.0.0.0 0.0.0.0 192.168.2.251 ! dnshost nameserver 202.78.206.6 ! service ez-setup ! user add guest guest low ! auto-script autorun.inf ! ! ! ! ! ! VoIP configuration. ! ! ! Voice service voip configuration. ! voice service voip fax protocol t38 redundancy 0 fax rate 9600 h323 call start fast h323 call tunnel enable busyout monitor gatekeeper no busyout monitor callagent busyout monitor voip-interface ! ! ! Voice port configuration. ! ! FXS voice-port 0/0 ! ! ! FXS voice-port 0/1 ! ! ! ! ! Pots peer configuration. ! dial-peer voice 1 pots destination-pattern 123456 port 0/0 user-name 123456 user-password xxxx ! ! ! ! Voip peer configuration. ! ! ! dial-peer voice 1000 voip destination-pattern T session target sip-server session protocol sip voice-class codec 1 dtmf-relay rtp-2833 no vad ! ! ! ! Gateway configuration. ! gateway h323-id voip.192.168.2.110 register ! ! ! Codec classes configuration. ! voice class codec 1 codec preference 1 g729 codec preference 2 g7231r63 codec preference 3 g7231r53 codec preference 4 g711alaw codec preference 5 g711ulaw ! ! ! ! SIP UA configuration. ! sip-ua user-register sip-username 123456 sip-password xxxx sip-server au.voxalot.com sev enable register e164 ! ! ! MGCP configuration. ! mgcp codec g711ulaw ! ! ! Tones ! ! ! ! |