Current VoXaLot status - Page 3

pym · 10-05-2006, 09:35 AM

Quote:

Originally Posted by lithgow

I have had my SPA-3000 set up with Voxalot as a gateway in order to add two extra providers for outgoing calls.

My voxalot status shows these two providers as being registered correctly, but when I try to dial out to them via voxalot.com.au, I get a busy tone and an invalid status showing for Line 1 on the SPA-3000's Info page.

I've been having exactly the same problem, although only using one VSP (MyNetFone) via Voxalot. Showing registered, but any calls end up with a Reorder status being reported on the Sipura.

Ron · 10-05-2006, 10:50 AM

Martin,

FWD is now showing 'Registered' and incoming calls are working again.

Thank you!

Ron

martin · 10-05-2006, 12:26 PM

Thanks Ron, I was watching it and it was very slow to register FWD entries. I'm not sure if the problem is on our side or FWD however most other providers like sipphone did register alot quicker.

Anyway glad it is ok. Thanks.

evilbunny · 10-05-2006, 03:40 PM

What about sipme, I added a new account, and it hasn't registered, yet it registers ok with the same details in asterisk...

martin · 10-05-2006, 10:19 PM

Quote:

Originally Posted by evilbunny

What about sipme, I added a new account, and it hasn't registered, yet it registers ok with the same details in asterisk...

The Oz registration cycle is at 4:30am AEST. If it is still not registered PM my the SIPME username and I will check.

evilbunny · 10-05-2006, 10:21 PM

Why does it take so long to add a new provider? Considering it said please wait up to 30 minutes on the page

martin · 10-05-2006, 10:34 PM

New providers are added in real time for outbound calling. For registrations however, we currently have a 24 hour turnaround while until we deploy our new registration functionality (yes the page should be updated to reflect this

)

This limit was put in place a couple of months ago to work around limitations with the current registration framework.

lithgow · 10-06-2006, 01:02 AM

Quote:

Originally Posted by pym

I've been having exactly the same problem, although only using one VSP (MyNetFone) via Voxalot. Showing registered, but any calls end up with a Reorder status being reported on the Sipura.

Yeah, I'm using MyNetFone as well. Maybe that's the problem...

evilbunny · 10-06-2006, 01:30 AM

Quote:

Originally Posted by martin

New providers are added in real time for outbound calling. For registrations however, we currently have a 24 hour turnaround while until we deploy our new registration functionality (yes the page should be updated to reflect this

)

This limit was put in place a couple of months ago to work around limitations with the current registration framework.

I had a lot of trouble using SIPME with voxalot, I had the same problem with asterisk until I added:

fromdomain=sip.sipme.com.au
fromuser=1777xxxxxx

in the sip.conf, after that it worked fine every time, although it might be a coincedence with voxalot...

10-05-2006, 12:26 PM	#23
martin Join Date: Feb 2006 Posts: 2,930 Thanks: 528 Thanked 646 Times in 340 Posts	Thanks Ron, I was watching it and it was very slow to register FWD entries. I'm not sure if the problem is on our side or FWD however most other providers like sipphone did register alot quicker. Anyway glad it is ok. Thanks. __________________ Martin Please post support questions on the forum. Do not send PMs unless requested.

10-05-2006, 10:34 PM	#27
martin Join Date: Feb 2006 Posts: 2,930 Thanks: 528 Thanked 646 Times in 340 Posts	New providers are added in real time for outbound calling. For registrations however, we currently have a 24 hour turnaround while until we deploy our new registration functionality (yes the page should be updated to reflect this ) This limit was put in place a couple of months ago to work around limitations with the current registration framework. __________________ Martin Please post support questions on the forum. Do not send PMs unless requested.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Voxalot and Sipura/ATA Tutorial: A Comprehensive Walkthrough	ctylor	Voxalot General	5	04-28-2010 12:52 AM
Can't get voice packets to bypass VoXaLot	v164	Voxalot Support	35	08-23-2009 10:25 PM
VoXaLot not working with PBXes (VoXaLot as an extension of PBXes)	wilsonhlacerda	Voxalot Support	31	12-09-2007 02:30 PM
Which VoXaLot services are B2BUA?	v164	Voxalot Support	6	07-23-2007 01:48 PM
New to Voxalot some feedback - what does provider status "-" mean ??	7iron	Voxalot Support	5	03-19-2007 11:26 AM

10-05-2006, 10:50 AM	#22
Ron Join Date: Feb 2006 Posts: 447 Thanks: 4 Thanked 8 Times in 8 Posts	Martin, FWD is now showing 'Registered' and incoming calls are working again. Thank you! Ron

10-05-2006, 03:40 PM	#24
evilbunny Senior Member Join Date: Feb 2006 Posts: 176 Thanks: 0 Thanked 14 Times in 10 Posts	What about sipme, I added a new account, and it hasn't registered, yet it registers ok with the same details in asterisk...

10-05-2006, 10:21 PM	#26
evilbunny Senior Member Join Date: Feb 2006 Posts: 176 Thanks: 0 Thanked 14 Times in 10 Posts	Why does it take so long to add a new provider? Considering it said please wait up to 30 minutes on the page