![]() |
|
Voxalot Tips, Tricks & HowTo's Tips and Tricks for Voxalot |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Member
![]() Join Date: Sep 2008
Posts: 33
Thanks: 7 Thanked 5 Times in 1 Posts ![]() |
![]() LINKSYS IVR COMMAND LISTING Managing your VoIP ATA via a telephone keypad If you notice an IVR command missing; please respond below, so it can added to the list! All of these commands work on my devices; SPA901, PAP2T and SPA3102, and i'm more than happy to share them with the community. Just say or click "Thanks!" below! ![]() Additionaly, if you have any difficulty using this list, then please post a question! ![]() --------------------------------------------------------------------------- Download this page as a document: - here. (31kb) Linksys SPA VoIP Admin Provision Guide v3.0 - 94 Page PDF: - here (2,933kb) --------------------------------------------------------------------------- Let's begin with an example: - Lift the handset of the phone connected to your ATA (or network VoIP Phone, SPA9xx's etc.), - Dial **** to initiate the IVR Menu (four asterisk's), - Wait for the 'deep' robotic voice, - Enter your "command" using the keys on the handset/phone (see below), - Press # (hash/pound) to send the command to the ATA (after entering a 3 digit command), - Wait for a response, and then key in another command/action, - Hang up once finished! --------------------------------------------------------------------------- :: CHECK THE STATUS OF A DEVICE :: Check DHCP Status, if 'enabled'/'disabled': - 100 Check Local IP Address of Device: - 110 (see 210 below, for some devices) Check Network/Subnet Mask: - 120 Check Gateway IP Address: - 130 Check MAC Address: - 140 Check Firmware Version: - 150 Check Primary DNS Server IP Address: - 160 Check Internet Web Server Port: - 170 Check Local IP Address of Device: - 210 :: CHANGING A SETTING :: Set Internet Connection Type: - 101 - Press 1 - Use DHCP - Press 2 - Use Static IP - Press 3 - Use PPPoE Set Static IP Address: - 111 - Use keypad to enter numbers - Use * (asterisk) to represent a dot or decimal point - e.g. 192*168*1*150 Set Network/Subnet Mask: - 121 - Use keypad to enter numbers - Use * (asterisk) to represent a dot or decimal point - e.g. 255*255*255*0 Set Gateway IP Address: - 131 - Use keypad to enter numbers - Use * (asterisk) to represent a dot or decimal point - e.g. 192*168*1*1 Set Primary DNS Server IP Address: - 161 - Use keypad to enter numbers - Use * (asterisk) to represent a dot or decimal point - e.g. 192*168*1*1 :: REBOOTING & FACTORY RESET THE DEVICE :: 'Enable'/'Disable' Web-Based Utility/Access: - 7932 - Use keypad to enter numbers - 1 to enable - 0 to disable Manual Reboot: - 732668 - Hang up once hearing 'Option Successful', - Useful when managing devices across a network. Factory Reset: - 73738 - 1 to confirm - * to cancel User Factory Reset: - 877778 - 1 to confirm - 0 to cancel --------------------------------------------------------------------------- I hope this has helped and please let me know if i've forgotten anything??? (: Last edited by VoipAlot; 09-21-2008 at 06:57 AM. |
![]() |
![]() |
![]() |
#2 |
Member
![]() Join Date: Sep 2008
Posts: 33
Thanks: 7 Thanked 5 Times in 1 Posts ![]() |
![]() Is everyone sure I haven't forgotten anything?
Cheers! (: |
![]() |
![]() |
![]() |
#3 |
Member
![]() Join Date: Sep 2008
Posts: 33
Thanks: 7 Thanked 5 Times in 1 Posts ![]() |
![]() Is anyone aware of the iVR commands available for the Cisco Phone Handsets?
i.e. non-Linksys devices? Thank you very much! ![]() |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
HowTo: 6 Steps To Tune Your Voice Quality | martin | Voxalot Tips, Tricks & HowTo's | 13 | 12-27-2010 11:36 AM |
Voxalot and Sipura/ATA Tutorial: A Comprehensive Walkthrough | ctylor | Voxalot General | 5 | 04-28-2010 12:52 AM |
Can't get voice packets to bypass VoXaLot | v164 | Voxalot Support | 35 | 08-23-2009 10:25 PM |