|
SIP Broker Support Support for the SIP Broker service. |
Thread Tools | Display Modes |
04-21-2007, 04:08 PM | #1 |
Senior Member
|
One Simple Qustion !!!
How i can make my Home Number as a DID number and give it to the SipBrooker i have two PSTN numbers and i wont to give one to the SipBrooker , so what do i need to do that ....
I have an ADSL spped of ((5MB / 512 KB)) I have an SPA-3102 (( LinkSys ATA )) I have 24 hours working server .. what do i need elase i can provide and what is the method Thanks in advance Last edited by amroe; 04-21-2007 at 04:09 PM. Reason: spelling |
04-24-2007, 04:50 AM | #2 | |
Join Date: Mar 2006
Posts: 188
Thanks: 4 Thanked 64 Times in 41 Posts |
Quote:
1) You need some hardware/software that will answer the DID when it rings, and then prompt the user for digits (that are remembered for step #2). 2) After the digits (and don't forget the *-key as a "digit", because the *-key is very important in SIP Broker dialing) are received, you need some way to send a SIP call to: digits_the_user_dialed@sipbroker.com (where "digits_the_user_dialed" is the exact sequence of digits the user dialed in). i.e. A SIP Broker PSTN number essentially answers the phone, collects the digits, and then uses those collected digits to mimic normal use of SIP Broker. NOTE: If your DID is one that can be redirected to another person's server, SIP Broker can help you with those two steps if you wish (as we do have a server that can handle the voice prompting and redirecting). Or, if you like, you can do the whole thing yourself. Which could easily get used up quickly, if you are constantly hosting VoIP calls via your donated DIDs. I'm not telling you not to do it, just warning you that whichever server hosts the DIDs also ends up paying the bandwidth for any VoIP calls made with those DIDs... If your DIDs are already VoIP DIDs that can be redirected to another server, than this isn't needed. However, if they are real telco PSTN lines, than you will need some device to convert them to VoIP. And an SPA-3102 can be used for convert a single telco phone line into a 1 DID (one user at a time) VoIP line. In fact, just an SPA-3102 + a PSTN line + a little bandwidth is enough hardware to make a single line SIP Broker PSTN number. What you would want to do (in that case), is have the SPA-3102 answer your PSTN number, and then allow the calling in user to dial digits which your SPA-3102 will send to the sipbroker.com proxy... If you can install Asterisk :: An Open Source PBX and telephony toolkit | on that server, that would give you much more options for automated voice prompting, etc. However, if you just arrange to redirect those DIDs to a SIP Broker server (assuming they are DIDs from someplace that lets you "redirect" them), than you wouldn't have to worry about "rolling your own" (as SIP Broker already is setup to host such DIDs). |
|
04-24-2007, 12:35 PM | #3 | |
Member
Join Date: Mar 2007
Posts: 93
Thanks: 15 Thanked 24 Times in 16 Posts |
Access number in China
Quote:
There isn't any SIP Broker PSTN access number in China. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Just a simple thank you to Voxalot. | bolat | Voxalot Support | 3 | 04-28-2007 09:05 PM |
Help with simple Dial Plans PSE? | vk4akp | Voxalot Support | 12 | 03-24-2007 12:27 PM |
simple examples for web callback | dougnash | Voxalot Support | 1 | 06-20-2006 03:47 AM |
Simple WAP interface | evilbunny | e164.org Support | 0 | 05-26-2006 02:17 AM |
Simple complete Dialing Plans | pmerrill | Voxalot Support | 3 | 05-04-2006 07:47 AM |