|
Voxalot Support Support for the Voxalot service. |
Thread Tools | Display Modes |
10-26-2008, 04:39 PM | #1 |
Junior Member
Join Date: Oct 2008
Posts: 26
Thanks: 3 Thanked 1 Times in 1 Posts |
Provider selection & caller ID
Hello
I just opened a voxalot account and configured voipdiscount & nonoh. I can call but I have three questions: 1st. How can manually select a provider (i.e to call #10030210xxxxxx and the call go from nonoh and #20030210xxxxxx uses voipdiscount) 2nd. No matter what I did I was not able to sent the caller ID. 3nd. The FUP is solved (I have read about this in the forum). Thank you sn |
10-26-2008, 05:15 PM | #2 | |
Join Date: Mar 2006
Posts: 188
Thanks: 4 Thanked 64 Times in 41 Posts |
Quote:
Of course, once VoXaLot is routing the calls as you desire, it's simply a matter of setting up your VoIP adapter (likely it's "dial plan") to route all calls to VoXaLot, and let VoXaLot sort it out for you. NOTE: If you have a LinkSys model VoIP adapter, you may not be able to use the #-key for this, because of how LinkSys model adapters treat the #-key specially. However, all 10 digits are available for routing decisions, as is the *-key. |
|
10-26-2008, 06:33 PM | #3 |
Junior Member
Join Date: Oct 2008
Posts: 26
Thanks: 3 Thanked 1 Times in 1 Posts |
Thank you DracoFelis
Yes I have a linksys ATA. I manage to select various providers using 1, 2 etc in front of the number. So, this is exactly what i was asking for. Some times it shows caller ID, but not always and never in mobile. Directly from my ATA it shows number only in mobile. Quality is about 20% worst than using the provider directly in ATA. Is that normal? Thank you sn |
10-26-2008, 07:23 PM | #4 | |
Join Date: Mar 2006
Posts: 188
Thanks: 4 Thanked 64 Times in 41 Posts |
Quote:
However, by default VoXaLot inserts itself in the call path between you and your provider. So the call path is longer (because it has to relay via VoXaLot) and this extra "latency" can sometimes (but not always) result in a little lower quality connection. Another thing that can lower the quality of the connection, is using a different CODEC (voice transmission algorithm) between you and VoXaLot and VoXaLot and your provider. For example, if you use G711u to connect to VoXaLot, but then use G729 as the first/default CODEC for your provider in VoXaLot, then VoXaLot will be constantly converting between the two (what is known as "transcoding") during your phone call. And transcoding always seems to result in lower quality audio. So, if possible, using the same CODEC for your connection with VoXaLot and VoXaLot's connection to your provider(s) is likely to give better audio. And make sure you are connecting to the proper VoXaLot server (the one with the lowest latency to you and your providers). For example, if you are in the USA, be sure your VoIP adapter is using "us.voxalot.com" vs one of the other VoXaLot proxies (or "au.voxalot.com" if you are in Australia, etc). Because while any of the servers will work, using the server closest (on the internet), to you and your providers, will generally result in the fewest (internet related) distortions of the sound. Finally, in some cases it is possible for VoXaLot to get out of the way and leave the final connection directly between you and your provider (after VoXaLot does all the setup). This option is NOT on "by default", as it has the risk of blocking the audio if everything isn't setup just right. However, this option can (when it works) improve audio quality (by lowering latency and possibly jitter). So if you want to experiment with this option, follow the instructions here: HowTo: 6 Steps To Optimize Your Audio - Voxalot FAQ |
|
10-26-2008, 08:04 PM | #5 |
Junior Member
Join Date: Oct 2008
Posts: 26
Thanks: 3 Thanked 1 Times in 1 Posts |
Thank you a lot DracoFelis
The quality issue is solved. It was a bad codecs negotiation, but to be safe I enabled NAT too. Caller ID works for fixed lines but not for mobiles. Regards sn |
10-29-2008, 01:26 PM | #6 |
Junior Member
Join Date: Jan 2008
Location: Australia
Posts: 23
Thanks: 10 Thanked 3 Times in 3 Posts |
[Caller ID works for fixed lines but not for mobiles.
I have the opposite issue in that Caller ID works to mobiles but not to landlines? Can anyone assist on this? |
10-29-2008, 09:09 PM | #7 |
Join Date: Feb 2006
Posts: 243
Thanks: 8 Thanked 130 Times in 72 Posts |
|
10-29-2008, 10:21 PM | #8 |
Junior Member
Join Date: Jan 2008
Location: Australia
Posts: 23
Thanks: 10 Thanked 3 Times in 3 Posts |
|
10-30-2008, 11:32 AM | #9 |
Junior Member
Join Date: Jan 2008
Location: Australia
Posts: 23
Thanks: 10 Thanked 3 Times in 3 Posts |
Did some isolation testing & it is not a Voxalot issue as I thought, seems to be something to do with my Billion router..
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Voxalot and Sipura/ATA Tutorial: A Comprehensive Walkthrough | ctylor | Voxalot General | 5 | 04-28-2010 12:52 AM |
Voxalot does not release Registered Number once deleted from Voice Service Provider L | xvaiox | Voxalot Support | 4 | 08-05-2007 09:55 AM |
Using same provider in two Voxalot accounts | clundestad | Voxalot Support | 1 | 04-20-2007 11:32 AM |
Any one knows why my caller id is always "blah" | yuzyin | Voxalot Support | 1 | 07-09-2006 11:41 AM |