Voxalot / SIP Broker Support Forums

Voxalot / SIP Broker Support Forums (https://forum.sipbroker.com/index.php)
-   SIP Broker Support (https://forum.sipbroker.com/forumdisplay.php?f=9)
-   -   Dial Plan Setup (https://forum.sipbroker.com/showthread.php?t=4206)

kieranmullen 07-31-2009 05:53 PM

Dial Plan Setup
 
Which device would best support this? I currently have a linksys pap2tna

I would like 1 sip registration for domestic, 1 sip registration for international and sipbroker lookup. Is this supported on this device on the same line?

Thanks!

emoci 08-01-2009 05:32 AM

Quote:

Originally Posted by kieranmullen (Post 24427)
Which device would best support this? I currently have a linksys pap2tna

I would like 1 sip registration for domestic, 1 sip registration for international and sipbroker lookup. Is this supported on this device on the same line?

Thanks!

I am a bit unclear on what you're asking:

1. Domestic VSP
-Do you have the need to receive Incoming Calls with this Provider (eg. have a DID with them)?
-Do you wish to make outgoing calls with this provider?
-Which provider is it?

2.International VSP
-Do you have the need to receive Incoming Calls with this Provider (eg. have a DID with them)?
-Do you wish to make outgoing calls with this provider?
-Which provider is it?

3. SipBroker Lookup
-Do you need to be able to call *SipCode-Number destinations?
-Do you need to perform ENUM lookups over SipBroker?

Finally, is your intention to use only your ATA, or would it be ok to have a middleman like VoXalot involved?

kieranmullen 08-03-2009 01:21 AM

Thank you for your response. I believe most of the questions you were asking me were not relevant anyway. That being said I got it answered...

Quote:

No. There have been reports that you can do it if both accounts have the same userid and password. Presumably that is because the firmware only knows how to respond with one set of userid/password. The dial plan syntax for uid, pwd outlined in the ATA Administration Guide is specified for the SPA3102 but I would question that the syntax works properly.

kieranmullen 08-06-2009 08:25 AM

From this page SIP Broker Wiki : SIP Broker Wiki

These do not work Should they be removed from the wiki? I see I was the last one to edit the wiki page.

•Call 1-516-687-5089. After playing an ad, it tells you whether you connected via ENUM (free call) or PSTN (paid call). (If you would like the call to be "ENUM or bust", then dial it as *013-1-516-687-5089.)

I am currently using this entry
L:20,S:7,( x | *xx | 911S0 | 1[2-9]xx[2-9]xxxxxxS0 <:@sipbroker.com> | [x*][x*]. <:@sipbroker.com> | <#:>[x*][x*]. )

Any idea How I could I get either of these to be prepended AFTER it fails siproker lookup?

An element like this would prepend 9 to all numeric digits dialed |<:9>xx.|

An dial plan like this would put 9 ahead of anything including a leading asterisk: (<:9>[x*]x.)


*266-300

kieranmullen 09-28-2009 07:18 PM

OK Another question... Using from the FAQ
L:20,S:7,( x | *xx | 911S0 | 1[2-9]xx[2-9]xxxxxxS0 <:@sipbroker.com> | [x*][x*]. <:@sipbroker.com> | <#:>[x*][x*]. )

How could I lookup all dialed numbers in sipbroker using (e164.org) first?

Thank you


All times are GMT. The time now is 10:38 PM.

Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.