Voxalot / SIP Broker Support Forums

Voxalot / SIP Broker Support Forums (http://forum.sipbroker.com/index.php)
-   Voxalot General (http://forum.sipbroker.com/forumdisplay.php?f=14)
-   -   Post Your VoXaLot Dial Plan (http://forum.sipbroker.com/showthread.php?t=292)

ptruman 10-08-2006 02:13 PM

Egad, it's taken a while... (UK/Voxalot/SipBroker dialplan)
 
Code:

L:5,S:5,(764xxxx<#:>S0|<S0#><:@gw0>|999S0<:@gw0>|xxxxxxx<:@gw0>|00x.<:@gw0>|0[12578]x.<:@gw0>|<00:>x.<#:@sipbroker.com>|<:44121>xxxxxxx<#:@sipbroker.com>|<0:44>[12578]x.<#:@sipbroker.com>|*x.|*x.<#:>|x.)
Chunk by chunk :

L:5,S:5 = Long & short interdigit gaps set to 5 seconds

Private DialPlans
764xxxx<#:>S0 = I have a friend with a private Asterisk PBX. I have Voxalot setup to register with his PBX, and setup a Voxalot dialplan so that if I dial 764 and any 4 digit extension, it routes to Voxalot, which connects the call via his PBX. The trailling # is picked up and used to make the call immediately, but the actual # is removed. I could set this up as a Gateway on the SPA3102 but the Voxalot GUI is nicer to use :)

You'll see why the private dialplans have to be at the front later on...

The useful PSTN bits

<S0#><:@gw0> = Pressing # will get me an outside line (PSTN) dialtone, immediately

999S0<:@gw0> = Dialling 999 will immediately dial 999 on the outside line (PSTN) immediately

Local, Regional/National and International PSTN dialling

xxxxxxx<:@gw0> = Any 7 digits will use the PSTN line. I live in an area where local numbers are 7 digits. Some may be in 6 digit codes, remove an x as appropriate :)

00x.<:@gw0> = Anything starting 00 will use PSTN (00 is the UK international dial prefix, so 001xxxxxxxxxx will dial a US number over PSTN)

0[12578]x.<:@gw0> = Anything starting 01, 02, 05, 07 or 08 will dial that number over PSTN (national/regional calls)

ENUM alternative International dialling via SipBroker

<00:>x.<#:@sipbroker.com> = Anything starting 00 and ending with a # will remove the leading 00 AND the #, and attempt a dial via SipBroker (i.e. dialling 0015166875089# will use ENUM lookup via SipBroker and actually call 15166875089@SipBroker.com)

ENUM alternative Local dialling via SipBroker

<:44121>xxxxxxx<#:@sipbroker.com> = Any 7 digits ending with a # will be prefixed with 44 (UK dialling code) and 121 (my area code), the trailing # will be removed, and attempt a dial via SipBroker (i.e. dialling 1234567# will use ENUM lookup via SipBroker and actually call 441211234567@SipBroker.com)

Now, remember those "Private DialPlans" back at the top of this message? :)
The one example I have above is 764xxxx#
The astute amongst you will notice that <:44121>xxxxxxx<#:@sipbroker.com> will change 7 digits to a local SIP lookup as described in the above paragraph. The DialPlan is parsed from left to right, so if I put my Private DialPlan AFTER this chunk, it is always "missed", as the xxxxxxx matches first....

Thus, ensure your private dialplans (for any exchanges/or forwards which are NOT covered by Voxalot/SipBroker) are at the FRONT :)

ENUM alternative Regional/National dialling via SipBroker

<0:44>[12578]x.<#:@sipbroker.com> = Anything starting 01, 02, 05, 07 and 08, ending with a # will have the leading 0 removed, be prefixed with 44 (UK dialling code),the trailing # will be removed, and attempt a call via SipBroker (i.e. dialling 0800123456# will use ENUM lookup via SipBroker and actually call 44800123456@SipBroker.com)

Voxalot -> SipBroker calls
*x. = Anything starting with a * will go via Voxalot "as is" - so dialling *393613 will call the FWD echo test

*x.<#:> = The same as the above, but will allow you to press # to make the call without waiting, but will remove the # from the dialled number (otherwise Voxalot would try and call *393613# which doesnt work...)

Normal Voxalot calls

x.<#:> = Will make calls ending in # over Voxalot, removing the # before dialling. This enables anything you dial ending in # to try going via Voxalot (i.e. 500#)

x. = Anything else which hasn't matched an existing ATA dialplan, and hasn't ended in a #, route over Voxalot

REMEMBER : These are all on your ATA. Your Voxalot dialplans only come into play when/if the call hits Voxalot.

So, in a nutshell, pressing # to start with gets an outside line. Ending a number with # means it will force it over the net (via SipBroker or Voxalot as appropriate). Not using # will drop to PSTN & dial - after 5 seconds, which means it's transparent for anyone not used to the system (just a bit slower than they may be used to).

441516 10-09-2006 03:08 AM

Thanks
 
"0[12578]x.<:@gw0> = Anything starting 01, 02, 05, 07 or 08 will dial that number over PSTN (national/regional calls)" I tried to add and it says its invalid plan. Do you think there is an error?

ptruman 10-09-2006 12:26 PM

Quote:

Originally Posted by 441516 (Post 3355)
"0[12578]x.<:@gw0> = Anything starting 01, 02, 05, 07 or 08 will dial that number over PSTN (national/regional calls)" I tried to add and it says its invalid plan. Do you think there is an error?

There is no error - paste my whole dialplan into your unit, and it will work. I suspect you have missed a | character.

The whole dialplan needs to be wrapped in brackets (), so if you're just testing it on it's own, you'd need :

Code:

(0[12578]x.<:@gw0>)
If you're testing it with other rules, the rules are | separated, so you'd get

Code:

(rule 1 here|0[12578]x.<:@gw0>|rule 2 here)

441516 10-10-2006 01:19 PM

Thanks Ptruman
 
Very helpful.

ptruman 10-13-2006 11:02 AM

Ok, I've now subscribed to voip.co.uk in the UK, for cheap PSTN calls.

As a result, I've decided to hook into SipBroker for ENUM lookups, so I only use PSTN when I have to...

Again, this is on my SPA3102.

My new dialplan is thus :

Code:

L:5,S:5,(<*:>764xxxx<#:@gw1>S0|<S0#><:@gw0>|999S0<:@gw0>|<00:>x.<#:@sipbroker.com>|<:44121>xxxxxxx<#:@sipbroker.com>|<0:44>[12578]x.<#:@sipbroker.com>|*xx<#:>,S0|*x.<:@gw1>|*x.<#:@gw1>|x.)
The ATA is registered with voip.co.uk, and gw1 is setup as Voxalot

Chunk by chunk :

<*:>764xxxx<#:@gw1>S0

I've setup 764 as a "dialplan" at Voxalot, for a friends PBX. I want to be able to dial *xxx (where xxx is the SIP shortcode in SipBroker/Voxalot), but Voxalot passes anything with a * direct to SipBroker - and 764 is my friends exchange, and not recognised by SipBroker. This bit removes the leading * when it's dialled, and fires 764xxxx (4 digit extension) at Voxalot. It also removes any trailing # pressed - still immediately connecting, but not sending the # which confuses Voxalot :)

<S0#><:@gw0>

When going "off-hook" on Line1, pressing # will immediately present a PSTN dialtone. This is to override any VOIP dialling and get an outside line if necessary.

999S0<:@gw0>
Route 999 straight to PSTN immediately. For emergency calls.

And now the SipBroker bits :)
If you've not already gone to look at it, go check http://www.sipbroker.com and http://www.e164.org. If someone (like I have) registers their PSTN number with e164, they can point it to a SIP number, and VOIP->PSTN callers will actually make a VOIP->VOIP call.

<00:>x.<#:@sipbroker.com>

In the UK, starting a number with 00 means it's international. This removes the 00, leaves the rest of the number intact, and passes it up to SipBroker. It also removes any trailing # pressed - still immediately connecting the call.

The SPA3102 uses # as a "I've finished dialling" message, but still sometimes sends it if pressed. I don't have to press #, but if I do, it does what it should, but also ensures it isn't passed along.

<:44121>xxxxxxx<#:@sipbroker.com>

This handles local calls. If you're in the UK and not in Birmingham, replace 121 with your local area code (less the leading zero). If your local numbers are not 7 digits long, change the number of xs accordingly. The dialplan prepends 44<area code> on the number, and fires it to SipBroker as above, again dealing with #s - no local numbers should start with 0, so this doesnt have anything to remove them.

<0:44>[12578]x.<#:@sipbroker.com>

This handles national calls, detected by dialling 0<digit>. Any leading zero is removed and replaced with 44, leaving the rest of the number intact. Again, this deals with #s and passes to SipBroker.

*xx<#:>,S0

The SPA3102 has *xx codes used for altering behaviour - *18 for example turns secure calls on. As I want to use * for calling via Voxalot, I use this dialplan to detect *xx# - however this again removes the #, dials the code, and presents me a dialtone so I can dial as normal.

I can go off hook and dial *18# and then dial a full number, or I can dial *18#<full number> and go off hook.

Interestingly, although this chunk of the dial plan is near the end, the , allows a new dialstring, which still checks the other dial plans - all calls route as they should.

*x.<:@gw1>

Route anything else starting with * via Voxalot

*x.<#:@gw1>

The same, forcing # removal - I can remove the previous rule I just haven't yet - this was there to check it behaved as intended.

x.

Route anything else via voip.co.uk

In a nutshell, I can now use the phone for PSTN calls, and they route over voip.co.uk for 1 ppm or 2 ppm depending on time of day. However, the SipBroker bit means if friends/family have a SIP address, they can register @ e164.org , and I will connect to them for free - and don't have to dial any other numbers. Any number not found in SipBroker just routes back to my provider and out.

Hopefully that will help someone out :)

nicois 11-01-2006 04:01 AM

Basic AU setup for billion/voxalot
 
Here's my setup.

In the billion dial plan, I do the following (which assumes you're in the '03' area code):
Code:

Use VOIP (via voxalot) for everything EXCEPT:
  000
  1800 / 1300 / 13 numbers
 Also:
  Translate 012 / 1223 into freecall equivalents
  Allow hash to be pressed to dial straight away
  Prepend with * to force to VOIP as a literal (e.g. a 1800 number which is in the US, or a sipbroker address)
  Convert all numbers to international format (to make the voxalot rules a bit simpler)

PHP Code:

voip endpoint 1 set digitmap '(000<:@pstn>|1[38]x.T<:@pstn>|<**:*>x.T<:@voxalot>|<*:>x.T<:@voxalot>|<1223:1800612219>x.T<:@pstn>|<013:1800612219>x.T<:@pstn>|<:613>[8-9]x.#<:@voxalot>|<:613>[8-9]x.T<:@voxalot>|<0011:>x.#<:@voxalot>|<0011:>x.T<:@voxalot>|<0:61>x.#<:@voxalot>|<0:61>x.T<:@voxalot>)' 

This makes the rules simpler in voxalot:

Code:

30          _614XXXXXXXX          ${EXTEN}          pennytel
92        _61XXXXXXXXX        ${EXTEN}        sipme
95        _ZXXXXXXXX.        ${EXTEN}        pennytel

So mobile and international calls go to one VSP, and national calls go to a different one.

rossmurray 12-05-2006 08:30 PM

I have a Speedtouch 780 (from my ISP bethere.co.uk) that I've connected my NTL dect phone into it's PSTN port1 and the PSTN connected to the landline. I don't really understand why but my dialplans yesterday didn't work but today they do. The only thing is today I've registered my PSTN number with e614.org and my enum looks at my voxalot number. Maybe that fixed it :confused:

Anyways I live in the UK and wanted free UK, Australia and Canada calls. I've found all these but the mobile calls will have to make do with almost exactly the same as my pay-as-you-go mobile.

This is what I have set as my dialplans:

1 _7. 004420${EXTEN} Voipdiscount
2 _8. 004420${EXTEN} Voipdiscount
3 _020. 0044${EXTEN:1} Voipdiscount
4 _07. ${EXTEN} Sipgate
5 _01. 0044${EXTEN:1} Voipdiscount
20 _00 ${EXTEN} Voipbuster

V:cool:

ozimarco 12-06-2006 12:24 AM

Replacing one number with another.
 
In the Voxalot dial plan system, is it possible to replace a specific phone number with another? I tried this previously, before the non-geographic lookup was in place, by entering a specific 1300 number and its geographic replacement, but it didn't work.

martin 12-06-2006 12:41 AM

I just tried it and it worked ok. What I did was enter a specific number in the "Pattern" like _1300123456 (with the leading underscore) and in the "Replacement" field entered a completely different number and it routed ok.

affinity 12-07-2006 12:02 AM

I've done this in the past too, exactly as Martin has said.


All times are GMT. The time now is 04:40 AM.

Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.